Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
jocopod [2016/01/10 00:13] – admin | jocopod [2016/04/12 11:06] (current) – admin | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Anleitung ====== | ||
- | * Erst alles einstecken, dann C64 einschalten (sollte ja selbstverständlich sein, aber kann man ja nie zu oft sagen... ) | + | {{: |
- | * Es gibt 3 Taster, der einzelne ist Reset (des Arduinos). Momentan noch für nix gut, außer für, äh, naja Reset. Den Taster neben der grünen LED nenne ich mal Taster 1 und den neben der roten Taster 2. | + | |
- | * Im Normalbetrieb blinkt die grüne LED langsam (0,5 Hz). Die Rote leuchtet in Mittelstellung der X-Achse. | + | |
- | * Kalibrieren des Joysticks oder Lenkrads: | ||
- | - Calib 1 solange drücken, bis grüne LED schnell blinkt (2 Hz). | ||
- | - Beide Achsen in ihre Extreme bewegen | ||
- | - Beide Achsen in Mittel- bzw. Ruhestellung (Lenkrad in Mitte, Gaspedal loslassen) | ||
- | - Eine der Calib-Tasten oder JoyBtn1 oder JoyBtn2 drücken, Mittelstellung wird erfasst und Kalibriermodus verlassen. | ||
- | * Die Kalibrierung wird im EEPROM gespeichert und muss nur bei Wechsel des Eingabegeräts wiederholt werden. | ||
- | Die Paddlewerte werden folgendermaßen skaliert: | + | Das Jocopod |
- | * In Mittelstellung ungefähr 127 | + | |
- | * In den Extremlagen 0 bzw. 255 | + | |
- | * Dazwischen wird linear interpoliert | + | |
- | + | ||
- | Wenn man gern 0...255 auf einen kleineren Bewegungsbereich hätte, kann man bei Schritt 2 der Kalibrierung den Bereich, in dem man den Joystick oder das Lenkrad bewegt, entsprechend eingrenzen. | + | |
- | + | ||
- | + | ||
- | ---- | + | |
- | + | ||
- | + | ||
- | **Jocopod** can be used to adapt an analogue | + | |
- | + | ||
- | + | ||
- | ====== Manual ====== | + | |
- | + | ||
- | * Plug and unplug everything only when power is off! | + | |
- | * Jocopod has two LEDs and two buttons to let you calibrate your input device. The button next to the green LED is Button 1, the one next to the red LED is Button 2 (there is also a separate reset button but this is normally not needed). | + | |
- | * To calibrate a newly connected input device: | + | |
- | | + | |
- | | + | |
- | | + | |
- | - Press Button 1 or 2 or one of the joystick buttons to finish the calibration. | + | |
- | - In normal operation mode the green LED is blinking slowly (0.5 Hz) and the red one indicates the center position of the X-axis. | + | |
- | * The calibration is stored inside the Jocopod and has only to be repeated when changing the input device. | + | |
- | + | ||
- | *) Jocopod translates the given movement range to a full range of simulated paddle movement, so when you want to have full paddle deflection with less input device movement, move your input device only to your desired maximum positions in step 2. | + | |
+ | * [[: | ||
+ | * [[: | ||
+ | * [[: | ||
+ | * [[: | ||