Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
jocopod [2016/03/11 23:37] – admin | jocopod [2016/04/12 11:06] (current) – admin | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | === Vorläufiger Inhalt. Mehr folgt... === | ||
- | {{: | + | {{: |
+ | Das Jocopod dient als Adapter zum Anschluss eines analogen PC-Joysticks oder -Lenkrads mit Gameport-Anschluss an den Controlport des Commodore 64 und setzt diese Signale entweder auf die zwei Paddle oder den digitalen Joystick um. | ||
- | + | | |
- | ====== Anleitung ====== | + | * [[: |
- | + | * [[:jocopod:firmware|Firmware]] | |
- | | + | * [[:jocopod: |
- | * Es gibt 3 Taster, der einzelne ist Reset (des Arduinos). Momentan noch für nix gut, außer für, äh, naja Reset. Den Taster neben der grünen LED nenne ich mal Taster 1 und den neben der roten Taster 2. | + | |
- | * Kalibrieren des Joysticks oder Lenkrads: | + | |
- | | + | |
- | - Beide Achsen in ihre Extreme bewegen | + | |
- | | + | |
- | - Eine der Calib-Tasten oder JoyBtn1 oder JoyBtn2 drücken, Mittelstellung wird erfasst und Kalibriermodus verlassen. | + | |
- | | + | |
- | * Im Normalbetrieb blinkt die grüne LED langsam (0,5 Hz). Die Rote leuchtet in Mittelstellung der X-Achse. | + | |
- | + | ||
- | Die Paddlewerte werden folgendermaßen skaliert: | + | |
- | * In Mittelstellung ungefähr 127 | + | |
- | * In den Extremlagen 0 bzw. 255 | + | |
- | * Dazwischen wird linear interpoliert | + | |
- | + | ||
- | *) Wenn man gern 0...255 auf einen kleineren Bewegungsbereich hätte, kann man bei Schritt 2 der Kalibrierung den Bereich, in dem man den Joystick oder das Lenkrad bewegt, entsprechend eingrenzen. | + | |
- | + | ||
- | + | ||
- | ---- | + | |
- | English Version: | + | |
- | + | ||
- | + | ||
- | + | ||
- | **Jocopod** can be used to adapt an analogue PC steering wheel or joystick to the C64 control port and simulates up to two paddles there. | + | |
- | + | ||
- | + | ||
- | ====== Manual ====== | + | |
- | + | ||
- | * Plug and unplug everything only when power is off! | + | |
- | * Jocopod has two LEDs and two buttons to let you calibrate your input device. The button next to the green LED is Button 1, the one next to the red LED is Button 2 (there is also a separate reset button but this is normally not needed). | + | |
- | * To calibrate a newly connected input device: | + | |
- | - Press Button 1 until the green LED starts blinking rapidly (2 Hz). | + | |
- | - Move all axes to their extremes *) (left, right, front and back). | + | |
- | - Center all axes (center steering wheel or joystick, release throttle). | + | |
- | - Press Button 1 or 2 or one of the joystick buttons to finish the calibration. | + | |
- | * The calibration is stored inside the Jocopod and has only to be repeated when changing the input device. | + | |
- | * In normal operation mode the green LED is blinking slowly (0.5 Hz) and the red one indicates the center position of the X-axis. | + | |
- | + | ||
- | *) Jocopod translates the given movement range to a full range of simulated paddle movement, so when you want to have full paddle deflection with less input device movement, move your input device only to your desired maximum positions in step 2. | + | |